​what Command Can Be Used on a Cisco Router to View the Routing Table?

Contents

Introduction

This document describes the use of the Microsoft Windows road command. Yous can change this information when you troubleshoot the Cisco Intelligent Contact Management (ICM) software.

Prerequisites

Requirements

Cisco recommends that you accept knowledge of these topics:

• How to troubleshoot Cisco ICM

• How to configure and troubleshoot TCP/IP

• How to troubleshoot Microsoft Windows

Components Used

This document is non restricted to specific software and hardware versions.

• Microsoft Windows NT and 2000

• Cisco ICM

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you lot understand the potential bear on of any command.

Conventions

Refer to Cisco Technical Tips Conventions for more information on document conventions.

Use the route Control

You tin can employ the road command to view, add together and delete routes on a Microsoft Windows NT server that runs Cisco ICM. Y'all can use these options with the road control:

            road            [-f] [-p] [command [destination] [mask subnetmask] [gateway] [metric costmetric]]

Control Options

This section explains each of the options that you lot can apply with the route control.

• The -f option clears the routing tables of all gateway entries. If you use the -f selection in conjunction with ane of the commands, the tables are cleared earlier you run the command.

• By default, routes are non preserved when you restart the system. Apply the -p pick with the add command to make a route persistent. Employ the -p choice with the print control to view the listing of registered persistent routes.

• The control pick specifies one of the half dozen commands in this table:

  Command	Definition
  print	Prints a road
  add together	Adds a route
  delete	Deletes a route
  change	Modifies an existing route
  destination	Specifies the figurer to send control
  mask subnetmask	Specifies a subnet mask to be associated with this route entry (default subnet mask is 255.255.255.255)

• The destination specifies the network destination of the route. The destination can exist an IP network address, an IP address for a host route, or a default route.

• A netmask is a 32-bit mask that y'all can use to carve up an IP address into subnets and specify the bachelor hosts in the network. If yous do not specify a netmask the default value 255.255.255.255 applies.

• The gateway selection specifies the default gateway. All symbolic names used for the destination or gateway are looked up in the network and computer name database files NETWORKS and HOSTS. If the control is print or delete, you tin utilise wildcards for the destination and gateway, or you can omit the gateway.

• The metric option assigns an integer cost metric (that ranges from 1 to 9999) which you lot can use to calculate the fastest, most reliable, and least expensive routes.

"IF" specifies the interface index for the interface over which the destination is reachable. If you practice not specify IF , an attempt is made to find the best interface for a given gateway.

Here is an example of the route command:

Examples

In order to view the entire contents of the IP routing tabular array, result the road print command.

In order to add a persistent route to the destination 10.nineteen.0.0 with the subnet mask of 255.255.0.0 and the side by side hop address of ten.10.0.1, issue the route -p add 10.19.0.0 mask 255.255.0.0 x.x.0.one command.

In lodge to view the routes in the IP routing tabular array that begin with "172.", issue the route print 172.* command.

In society to delete all routes in the IP routing table that brainstorm with "172.", issue the road delete 172.* command.

Related Information

• Technical Support & Documentation - Cisco Systems

tilleylork1968.blogspot.com

Source: https://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-intelligent-contact-management-enterprise/20524-route-command.html

Share this post